Specs
Gallery
Standard Accessories
Optional Accessories
Videos
SPECIFICATIONS
Item / Model VP-8 VP-10
Travels
Longitudinal Travel X-Axis 32.3″ 40.2″
Cross Travel Y-Axis 20″ 20.1″
Vertical Travel Z-Axis 21″ 23.6″
Table to Spindle 3.94″ min/25″ max 3.94″ min/27.5″ max
Spindle Center to Column 21″ 21″
Table
Table Working Surface 35.4″ x 20″ 42″ x 20.1″
Max. Workload on Table 1,100 lbs. 1,100 lbs.
Table Surface Ground/ T-slotted Ground/ T-slotted
No. of T-slots x Width 5 x 18 mm 5 x 18 mm
Table Height from Floor 35.4″ 35.4″
Spindle (standard)
Spindle Motor 20 HP / 10 min 20 HP / 10 min
Spindle Taper CAT-40 Dual Contact CAT-40 Dual Contact
Spindle Drive System Direct Drive Motor Direct Drive Motor
Spindle Speed 0 – 10,000 RPM 0 – 10,000 RPM
Spindle Bearings Steel Steel
Spindle (optional)
Spindle Motor 20 HP / 10 min 20 HP / 10 min
Spindle Taper CAT-40 Dual Contact CAT-40 Dual Contact
Spindle Drive System Direct Drive Motor Direct Drive Motor
Spindle Speed 0 – 15,000 RPM 0 – 15,000 RPM
Spindle Bearings Ceramic Ceramic
Automatic Tool Changer (Arm-Type)
Number of Tools 24 Tools (30 opt.) 24 Tools (30 opt.)
Tool Selection Bi-directional-Random Bi-directional-Random
Tool Change Time 2.0 Seconds Tool to Tool 2.0 Seconds Tool to Tool
Max. Tool Diameter 3″ with Adjacent Tools (6″ w/o) 3″ with Adjacent Tools (6″ w/o)
Max. Tool Weight 15 lbs. 15 lbs.
Tool Type CAT-40 (BT-40 opt.) CAT-40 (BT-40 opt.)
Max. Tool Length 10″ 10″
Ballscrews and Axis Motors
X-Y-Z Ballscrew Diameter 36 mm (1.4″) x 16 mm Pitch XY,
12 mm Pitch Z
36 mm (1.4″) x 12 mm
Ballscrew Type Class 3 Double-Nut Pre-loaded Class 3 Double-Nut Pre-loaded
Ballscrew Mounting Type Pre-tensioned Pre-tensioned
X-Y-Z Servo Motor 2.0 – 3.0 – 4.0 HP 3.0 – 3.0 – 4.0 HP
Servo Motor Mounting Direct Coupled Direct Coupled
Feeds
Rapid Traverse Rate X, Y, Z 1,890 (X, Y), 1,417 (Z) IPM 1,417 IPM
Acceleration X, Y, Z 1.18 G, 1.0G, 0.7G 0.7G
Cutting Feed Rate 0.01 – 394 IPM 0.01 – 394 IPM
Positioning Accuracy ± .0002″ Full Stroke ± .0002″ Full Stroke
Repeatability ± .0001″ ± .0001″
General
Coolant Tank Capacity 75 Gallons 75 Gallons
Machine Weight 11,000 lbs. 11,700 lbs.
Floor Space 128″ x 87″ x 108″ 128″ x 90″ x 110″
Machine Power Source* 208/220 Volts, 3 Phase, 75 Amps 208/220 Volts, 3 Phase, 75 Amps
Air Source 90 PSI 90 PSI

*Consult AMT or local AMT distributor for exact power requirements when ordering.

  • Spindle Cooler
  • Prep for High Pressure Coolant through the Spindle (pump system not included)
  • Flood Coolant System with programmable air blast
  • Air Blast for spindle
  • Auto Lubrication with alarm
  • Full Machine Enclosure
  • Halogen Work Lamp
  • Dual rear discharge screw type Chip Conveyors
  • Caterpillar chain type Chip Conveyor
  • Remote Handwheel
  • Heat Exchangers for control cabinets
  • Rigid Tapping
  • BT-40 Tool Changer
  • Unist Uni-Max cool lubricator for near dry machining – installed
  • Marposs VOP optical wireless part probe installed with training
  • Marposs VOTS optical wireless tool setter installed with training
  • Marposs VOP part probe + VOTS tool setter PACKAGE installed with training
  • Marposs WRP radio wireless part probe installed with training
  • Marposs WOTS radio wireless tool setter installed with training
  • Marposs WRP radio part probe + WOTS radio tool setter PACKAGE installed with training
  • Marposs ML75P laser tool setter installed with training
  • Auto Tool Presetter (Renishaw TS-27 wired)
  • Auto Tool Presetter (Renishaw OTS Wireless)
  • Renishaw NC4+ F145/85 3.35” laser tool setter (hardware only kit)
  • Renishaw NC4+ F145/85 3.35” laser tool setter installed with 2 days of training
  • Renishaw OMP-40 part probe for 2-D surfaces (hardware only kit)
  • Renishaw OMP-40 part probe installed with 2 days training
  • Renishaw OMP-400 part probe for 3-D surfaces (hardware only kit)
  • Renishaw OMP-400 part probe installed with 2 days training
  • Mitsubishi AC Drive for 4th Axis and 4th Axis interface cable set
  • Mitsubishi AC Drive for 5th Axis and 5th Axis interface cable set
  • Ganro DR-170 6.7”rotary table with Mitsubishi servo motor (4th axis interface req’d)
  • Ganro DR-200 8” rotary table with Mitsubishi servo motor (4th axis interface req’d)
  • Ganro DR-250 10” rotary table with Mitsubishi servo motor (4th axis interface req’d)
  • High Pressure Coolant thru Spindle 300 PSI complete
  • High Pressure Coolant thru Spindle 1000 PSI complete
  • 440/460/480 Volt operation
  • 30 Tool arm type ATC
  • 15,000 RPM, 20HP direct drive spindle
  • Auto Doors
  • Heidenhain Linear Scales on XYZ
  • Column Riser Block 4” or 6”
  • Column Riser Block 8”, 10”, or 12”
  • Oil Skimmer
  • Donaldson Torit MiniMist 1200 centrifugal mist collector
  • Graphite milling package with dust collection system, lid on top of machine, complete and installed

For Thanksgiving, our offices will be closed Thursday & Friday, November 26-27, 2020.